English version
Главная
Sales department
Krasnodar-North
+7 495 727-09-72
+7 812 380-33-46

Draw up a requisition note
МЕНЮ

New positions in our product range: Steel Sheet Art. 09G2S 2 mm
Riffled sheet 10mm
Galvanized steel sheet 2.5 mm
Galvanized steel sheet 1.2 mm
Galvanized wire 1.8 mm
Galvanized wire 2 mm
Galvanized wire 2.5 mm
Galvanized wire 3 mm
Galvanized wire 4 mm
Galvanized wire 6 mm


  Print version
Krasnodar-North

 

+7 495 727-09-72
Write a letter

View price - Krasnodar-North

BROWSE ALL PRICE LISTS

Metal warehouse "Krasnodar-North" is located at the exit from the village of Novotitarovskaya, along the Yeyskoye Highway, on the street Kraynyaya, 2A, after the monumet of the helicopter to the right, to a dead end. Directions can be seen on our website. Office and warehouse are located on the same territory, which facilitates the receipt of metal and paperwork immediately after loading.

To cope with the need of the Krasnodar Territory, in July 2008, an additional warehouse was opened in Novotitarovskaya station, which supplies building organizations and organizations consuming metal with metal - the city of Krasnodar, the city of Sochi and the entire Black Sea coast.

1. rebars of a1 steel grade(smooth), rebars a3 (corrugated) and rebars thermally hardened At800:
- a1: from 6 to 28 mm in bars; 6mm, 8mm and 10mm - also in coils
- a3 steel grades 35GS and A500S: from 6mm to 40mm in bars; 6mm, 8mm, 10mm also in coils, GOST R 52544-2006, GOST 5781-82, STO ASChM 7-93
- AT800 12mm, 16 mm, 6.7m long, GOST 10884-94

2. the entire range ofof I-beam on STO ASChM 20-93, GOST 19425, GOST 8239:
- 10, 12, 12Б1, 14, 16, 16Б1, 18, 20Б1, 20К1-К2, 20Ш1, 24М, 25Б1-B2, 25К1-К2, 25Ш1, 30Б1-Б2, 30К1-К2, 30Ш1-Ш2, 35Б1-B2 , 35K1-K2, 35Sh1-Sh2, 36M, 40B1-B2, 40K2-K5, 40Sh1-Sh2, 45B1-B2, 45M, 50B1-B2, 50Sh1-Sh3, 55B1-B2, 60B1, 60Sh1-Sh2, 70Sh1-Sh2

3. круги стальные ГОСТ 2590 по ст20, ст3, ст35, ст40Х, 45: от 12 мм до 340 мм

3. steel round bars GOST 2590 on st20, st3, st35, st40kh, 45: from 12 mm to 340 mm

4. flat rolled-stock :

- sheets of cold-rolled GOST 19904-90 (st08ps): 0.5 - 3.0 mm, cut in size 1250 * 2500

- sheets hot-rolled GOST 19903-90 (st3, st09G2S): 1.5 mm thick - 120 mm

- galvanized sheets GOST 14918-80: thickness 0.55 - 3, 0 mm, cutting 1250 * 2500

- expanded steel sheets GOST 14637-89: 406, 408, 506, 508, 510, 606, 608, 610

- sheets with rhombic and lentil corrugation GOST 8568-77: thickness from 3mm to 10mm

5. pipe rolling :

- electric welded pipes GOST 10704: from 57 * 3.0 to 426 * 8, including galvanized

- pipes seamless GOST 8732 and GOST 8734: from 32 * 4 to 426 * 12 unmeasured length

- water and gas pipes GOST 3262: from 15 * 2.5 to 50 * 3.5, including galvanized

- profile pipes GOST 30245, GOST 8639, TU: rectangular and square pipes with different wall thicknesses: from 15 * 15 * 1.5 to 300 * 300 * 6.0

6. angle bar of steel GOST 8509: from 25 * 25 * 3.0 to 250 * 250 * 20

7. channel steel GOST 8240: with parallel sides of flanges and with a slope of the inner edge of the flanges: height from 50 to 40 mm, width of flanges from 32 to 115 mm, including shaped channel GOST 8278

8. hexagonal bar GOST 2879, GOST 8560 (steel grades st35, st45): from 14 to 65

9. rolled wire according to GOST 30136, with a diameter of 6.5 mm in bars and coils

10. welded reinforcing mesh for reinforced concrete products, welded wire mesh BP-1 in cards 2 * 6 and 2 * 3 m, with a step of 50mm, 100mm, 150mm and 200mm, rod diameters from 3mm to 5mm

11. Annealed wire GOST 3282, with a diameter of 1.2 mm - 6 mm in coils; wire BP-1 3.0 mm - 3.8 mm in coils

12. steel strip GOST 103-76: 25 * 4 - 120 * 8 in bars, including galvanized in coils

13. metal square bar GOST 2591: 8mm, 10mm, 12mm, 14mm, 16mm, 20mm, 25mm, 50mm in rods 6m each

14. A roll-formed channel of own production 12m ND (unmeasured length no more than 1 piece on a pack)

Production of a roll-formed channel and a roll-formed angle bar under the order in the size of the customer, including a profile of high precision of profiling, in a range of the sizes is also possible:

- channel wall thickness 2,5mm-6mm

- wall height 40mm-250mm

- flange width 32mm-125mm

- Expanded metal sheet of our own production.

the sheet is presented in the standard product range: 406, 408, 506, 508, 510, 608, 610

width of sheets 1000 and 1200 mm, a cut-out type “scales” (expanded metal grating).

15. MANUFACTURING OF METAL STRUCTURES AND METALWARE according to customer’s drawings.3. steel round bars GOST 2590 on st20, st3, st35, st40kh, 45: from 12 mm to 340 mm

4. flat rolled-stock :

- sheets of cold-rolled GOST 19904-90 (st08ps): 0.5 - 3.0 mm, cut in size 1250 * 2500

- sheets hot-rolled GOST 19903-90 (st3, st09G2S): 1.5 mm thick - 120 mm

- galvanized sheets GOST 14918-80: thickness 0.55 - 3, 0 mm, cutting 1250 * 2500

- expanded steel sheets GOST 14637-89: 406, 408, 506, 508, 510, 606, 608, 610

- sheets with rhombic and lentil corrugation GOST 8568-77: thickness from 3mm to 10mm

5. pipe rolling :

- electric welded pipes GOST 10704: from 57 * 3.0 to 426 * 8, including galvanized

- pipes seamless GOST 8732 and GOST 8734: from 32 * 4 to 426 * 12 unmeasured length

- water and gas pipes GOST 3262: from 15 * 2.5 to 50 * 3.5, including galvanized

- profile pipes GOST 30245, GOST 8639, TU: rectangular and square pipes with different wall thicknesses: from 15 * 15 * 1.5 to 300 * 300 * 6.0

6. angle bar of steel GOST 8509: from 25 * 25 * 3.0 to 250 * 250 * 20

7. channel steel GOST 8240: with parallel sides of flanges and with a slope of the inner edge of the flanges: height from 50 to 40 mm, width of flanges from 32 to 115 mm, including shaped channel GOST 8278

8. hexagonal bar GOST 2879, GOST 8560 (steel grades st35, st45): from 14 to 65

9. rolled wire according to GOST 30136, with a diameter of 6.5 mm in bars and coils

10. welded reinforcing mesh for reinforced concrete products, welded wire mesh BP-1 in cards 2 * 6 and 2 * 3 m, with a step of 50mm, 100mm, 150mm and 200mm, rod diameters from 3mm to 5mm

11. Annealed wire GOST 3282, with a diameter of 1.2 mm - 6 mm in coils; wire BP-1 3.0 mm - 3.8 mm in coils

12. steel strip GOST 103-76: 25 * 4 - 120 * 8 in bars, including galvanized in coils

13. metal square bar GOST 2591: 8mm, 10mm, 12mm, 14mm, 16mm, 20mm, 25mm, 50mm in rods 6m each

14. A roll-formed channel of own production 12m ND (unmeasured length no more than 1 piece on a pack)

Production of a roll-formed channel and a roll-formed angle bar under the order in the size of the customer, including a profile of high precision of profiling, in a range of the sizes is also possible:

- channel wall thickness 2,5mm-6mm

- wall height 40mm-250mm

- flange width 32mm-125mm

- Expanded metal sheet of our own production.

the sheet is presented in the standard product range: 406, 408, 506, 508, 510, 608, 610

width of sheets 1000 and 1200 mm, a cut-out type “scales” (expanded metal grating).

15. MANUFACTURING OF METAL STRUCTURES AND METALWARE according to customer’s drawings.

Advantages and services of the Krasnodar-Sever metal warehouse:

a) cutting metal in size:

- oxy-fuel cutting

- cutting machine

- a band saw machine (precise cutting of round bars; sale of a part of a round bar, with a diameter of 80–250 mm)

- cutting of a leaf with a guillotine of up to 6 mm, as well as sale of a part of a leaf, with a thickness of 16 mm or more

- plasma cutting

b) straightening of rebar from coils to rods 6m each

c) delivery by truck in the region and in neighboring regions

d) direct delivery from the manufacturing plants to our warehouse or railway branch of the client

d) Rolled stock order picking in advance

e) wrapping the sheet with tape

g) moving metal from our other branches

All metal is certified, metal comes from such plants and plants as AO Zapsib, AO Severstal, AO Nizhneserginsky Hardware Metallurgical Plant, OOO BMZ Trading House, AO Nizhny Tagil Iron and Steel Works, OOO Abinsky ElectroMetallurgical Plant, Novolipetsk Metallurgical Plant OAO, Magnitogorsk Metallurgical Plant OAO, Enakievo Metallurgical Plant OAO, Taganrog Metallurgical Plant OAO, Alchevsk Metallurgical Plant OAO, Oskolsky Electrome OAO allurgichesky Plant ", AO" Metallurgical Plant. AK Serov, Omutninsky Metallurgical Plant ZAO, Ural Steel OAO, Trubny Plant OAO, Oktan OOO, Izhorskaya Trubnaya Kompaniya OOO, Pervouralsk Novotrubny Plant OAO, Chelyabinsk Pipe Rolling Plant OAO ", OOO" Production Company "DIA", OOO "Isaevsky Machine-Building Plant", AO "Asha Metallurgical Plant", as well as metal from Ukraine: PAO "ArcelorMittal Kryviy Rih".

To purchase metal from the warehouse “Krasnodar-North”, to find out the price per piece, to issue an invoice, you can contact the managers of the company. The availability of metal in stock, the price per ton can be viewed on our website.

A new product in the warehouses of the company AO "Metallotorg"!
Special attention of companies engaged in the production of decorative forged products!

Square bar 8x8, rectangle bar12x6

And also under the order of square bars 5x5, 6x6, 7x7, and rectangles 16x4, 14x7, the deadline for the order of 10-15 days

Several advantages of the new product:

Several advantages of the new product:

● - this is the convenience and ease of use of our products by end users,

● - due to the fact that all our rental is uncalibrated, it facilitates the work with it.

● - the process of production of our products allows you to avoid scale, which is convenient for further processing (painting, etc.).

● - it also does not have to be annealed, which leads to lower costs when working with it.

● As a result, our products are more flexible and do not require additional efforts when working with it.

Contact Information

Krasnodar region, village Novotitarovskaya, st. Krayniyaya, 2/12


It is easy to find us in the navigator by making the request "Metallotorg Krasnodar-North"

Business hours

Mon - Fri from 8:00 to 20:00,
(check in before 17:30) without lunch
Sat - Sat from 9:00 to 12:30

contact number

Navigator Link


Coordinates: 45.258653846296994, 39.01027651290486